Flow Frames: Frequently Asked Questions (FAQ).

Since there's an overflow from one palm card to the next, you can do this in a two-stage process:Create the document palm_cards.pdf with a geometry of 10cm x 8cm;Merge palm_cards.pdf into a separate A4 page document using pdfpages.

Here would be what we do for (1) above:Use pdfpages to merge palm_cards.pdf into a new document:Side note: The height of an A4 is 297mm pdf.

------

wi-fi p2p peers discovery downgrades wlan bandwidth

Radio scanning requires the wireless adapter to temporarily switch to different frequencies in order to find peers (or APs) across all available channels. This means that it cannot communicate with your main network due to being on the wrong frequency.(To avoid breaking the connection completely, the adapter rapidly jumps between scanning a random channel and transferring queued data on the regular channel.

).

------

Why is my MPIO connection to the SAN capped at 1 Gbps when using Linux?

What are your network cards? Integrated or Cards? What is the bus limitations of their connectivity? So basically are the network interfaces built into the motherboard or are they a PCI card of some form? What is the PCI bus, PCI-X or what? What is the bus speed. The system can't push more than the speed of the interface system bus

------

How to animate a rising sun in Adobe Illustrator CC?

You can simply create an action that exports (or save as a copy) your file and assign to it a function key.Now just move the sun 1/20th of the way up and then run the function key.Now repeat 20 times and it'll be complete quite quickly.

My answer here may be helpful on how to create an action (though this is for Photoshop, the proccess is the same)

------

Can I add motion blur to make animation less jerky?

Newer ffmpeg since version 4.1 includes new tmix video filter that mixes N adjacent frames together using weights. Now it is possible to do exactly what you have suggested: take an animation rendered with a N times higher framerate, merge every N frames together and lower framerate N times down to normal one, dropping out extra frames.Here's a script I created to test this flow:It creates an 8-seconds long animation of a black bar running left-right in a sine speed motion. See it on YouTube.

Thanks Gyan for the tip on achieving smooth animation by forcing full chroma sampling

------

Raspberry pi with drone for live streaming

You can actually do that with your pi already!Adafruit has a nice guide here:far as signal strength goes, the 802.11b/g/n USB dongles sold at Adafruit are quite good. I was able to get a signal strength of -74dBm through 14 feet of dirt (both dongles were buried in the ground as an experiment):imagine that through the air they would perform admirably

------

How, in Illustrator, do I release a clipping mask without releasing masks contained by that group?

Here I have four clipped objects, in a group, and the group itself is also clipped.If you open the layers palette, you can simply hide the clipping mask layer for any of the layers you want. There's no need to delete or release any clipping masks, or ungroup anything.

Edit:Another method is simply to move the group to a layer above the clip group. Then you can delete the left over/empty Clip Group if you no longer want it

------

What is the proper SEO handling of pages appearing in popups using IFRAMEs?

You could move your form urls to a folder that is blocked via robots.txt file. Then the search engines dont even bother crawling those.Your plan to integrate your forms via iframe in your CMS does not seem to be the best approach to me though, at least from a technical and user experience point of view.

------

How to poll UART while processing lots of other stuff

I believe some of the dsPIC family have DMA support in the MSSP peripheral, that will allow buffering of the input stream without cpu intervention up to a point, limited by available memory.Use an interrupt for processing the GPS data in chunks, just make sure the interrupt for your video processing work is set to a higher priority so it can bump the GPS handling interrupt

------

Flow Chart - While Loops process

Is the algorithm done once you remove one block that does not meet the threshold? If not, you need a loop that iterates over each block. You also need an exit condition if you have no blocks that fail to meet the threshold. Maybe something like this?Note, I don't normally do flow charts for my day-to-day activities so forgive me if I'm off base here.

------

Permissive vs. Strict API Message validation

The decisive factor in choosing between a strict or permissive interface is the expected use. What are the consequences of processing invalid input (or erroneously processing valid input) vs rejecting valid input?Even ignoring additional unrecognized parameters could cause the software to produce "incorrect" results, e.g. if a later version can interpret the additional parameter, leading to another outcome.

------

Is there a linux command/tool that will provide end-to-end bandwidth information between local and external host?

Not directly a bandwidth monitor per se, but you could givea try. It will produce a list of where your packets go through to reach its destination, and you will not need any access to any of those hops in between. Ping values in the list it produces are often indicative of where the bottleneck, or problem, is.

Same command exists on windows systems as:I know that is not exactly what you asked, but, what you asked, ie, learning bandwidth values between each of those hops, cannot be done. Because of privacy issues, if nothing else

------

Should I enabled 802.3x hardware flow control?

Experience here has been that 802.3x is very rarely what you want. In most circumstances you would be better served by either upgrades to the link speeds if there is congestion, or the implementation of "real" QoS/CoS (DSCP and 802.1p).The behavior of 802.3x has also been known to interact poorly with protocols with their own flow control such as TCP

------

How can I keep a single frame of a smoke cache?

You can insert keyframes for simulation visibility. Toggle the visibility button for the smoke sim to be off at frame 14 then insert keyframe. Then at frame 15 toggle visibility on then insert keyframe. Finally at frame 16, turn it off again and insert keyframe. It should not keep any of the cached data except for that single frame. FYI it will not show up on any other frames, just that one.

------

Does the Linux traffic control utility modify datagrams, IP packets, or frames?

tc affects the queuing discipline, i.e. the order in which outgoing "packets" are sent to the hardware. The implementation operates on sk_buff structs, and

the documentation for sk_buff seems to imply that the packet format is whatever the particular network interfaces uses (e.g. Ethernet packets for an Ethernet interface). So I'd assume netem corrupt adds corruption on this layer, which should be discovered through the layer-2 checksum (whatever layer 2 is for a particular interface). In addition, sk_buff contains pointers to the higher layer payloads, which explains why tc filter can act on them.

------

How exactly & specifically does layer 3 LACP destination address hashing work?

Since I just ended up back here, a few things I learned by now:

To avoid gray hair, you need a decent switch that supports a layer34 policy, and the same also in Linux.In quite a few cases the standards-perverting blowtorch called ALB/SLB (mode6) might work better. Operationally it sucks though.Myself I try to use 34 where possible, since I often want that bandwidth between two adjacent systems.I've also tried with OpenVSwitch and had once instance where that disrupted traffic flows (every first packet lost... i have no idea)

------

Best Cycle for developing new products?

I think that's a pretty standard way to do it, but don't serve the process if the process gets in the way of progress. I will never commit to a final deliverable (e.g., site map) before everything is done; IMHO, efficient UX work is never as neat as a waterfall-type project plan would indicate.

My own process is more like the curly line on a Hostess Cupcake (R.I.P.) than a straight line: I would also add that a critical part of my process is going back and forth between production fidelity levels: sketches to pixels and back

------

Limit FindMinimumCostFlow function to one vertex per path

Is it acceptable for your problem to change the costs associated to traversing the edges?If it is, then you can set the costs to:This seems to reproduce your desired flow:Note: for some reason my MMA defaults to really tiny arrow heads to indicate the directed graph edges. The non-highlighted arrows are there if you look reeeeally closely

------

What are good speeds for iSCSI and NFS over 1GB ethernet?

For just a single dd or bonnie (raw speed, linear writing) you should get pretty close to the wire-speed.But your bottleneck will be the disk array, once you start getting the random IO load of multiple VMs going, much more than the transport.Also, if you don't have a battery backed write cache with a significant amount of RAM, your performance will crater as soon as you start getting a lot of writes with any other IO going on.

------

iSCSI MPIO load balancing with HP P2000 SAN

We had a very similar setup a few years ago. It's a complex setup with lots of moving parts that you have to look through. Here are the main areas to check for performance:That's some real basic starting points. Worst case call up your vendors, they typically have good white papers or case studies around this kind of stuff

------

Measuring per-link latency/jitter/packet-loss

Check out Y.1731 protocol (or IEEE 802.1ag, or OAM). It's fairly easy to implement in software (I'm guessing that's what you're aiming at), and it's supported by all the physical network elements.There is a very naive

open-source Y.1731 implementation in C, which you can look at.Please note that Y.1731 is not designed to cross physical network boundary (i.e. requires that MAC addresses of both MEPs are known), so if you need to go through IP routing, you would want to encapsulate your Y.1731 frames within some tunneling protocol, like VXLAN or GRE.Hope this helps.

------

Can linear connections other than Levi-Civita connections be useful?

Absolutely yes. In Continuum Mechanics, a non-metric connection is used to describe uniform bodies, i.e., bodies that have intrinsically the same material properties at each point, but could be locally distorted, so that these properties appear to be dependent on the point. A beautiful reference is Epstein and Maugin (1990), The energy-momentum tensor and material uniformity in finite elasticity, Acta Mechanica 83, 127-133.

------

Simple way/techniques of arranging all the ideas and scenes in a plot?

You could try using a simple spreadsheet. Use the rows to represent characters or events and the columns to represent time frames or locations. You can put each of the elements into place to get a visual representation of your story flow. This will not only help you to develop a consistent timeline, but also to make sure that you don't have any characters showing up in two locations at the same time.

------

Wireframes first or after rough visual design sketches?

I like to work as collaboratively as possible. Ideal is when can optimise visual concepts which may improve design.I use wire-frames to ensure that the content, concepts and flow are well understood before engaging visual designer.

Particularly if there is a novel or tough design challenge then taking range of early (rough) wire-frames to the visual designer and together look for ways that the visual communication will and won't succeed with the concepts can evolve a better design

------

InDesign: applying paragraph style to text boxes

I made this an answer just to be kosher.If your copy is contained within a single box, you can apply a text style to that box.If your text flows/links to additional boxes, you can't apply a style via selecting the boxes. You have to apply the style directly to the text. I usually do a Select All on the copy within the box, then apply the style.You will also notice that if your text box flows/links and you have it selected (the box), your character and paragraph pallets will be grayed-out